OK folks! At first I am just going to paste the pattern instructions straight in here, for those of you who know what a Knitting Machine is all about, go for it!

For beginners wanting to learn how to machine knit a Baby Set, I will slowly add the full instructions with photos and movies as I get the time.

After completing the Baby Booties, please continue to the Baby Jacket or the Baby Beanie.

Fae Mason’s Passap Baby Set – Booties

One end Cashmillon & one end silky (low bulk)

26/25
Tension 3/3
Pink Strippers.
**Zig zag row from right to left.  Cast on comb in. Small weight outside each end of knitting.
Pushers on back bed 1 up 1 down
AX/N  – no arrows K 5 rows (no strippers in for 3 rows)
AX/N  – left arrow in K 2 rows.**   This = 8 r.
Tension 2½/2½
N/N K 12 r.
From left hand side on back bed place 3rd stitch on 4th, leave 2 stitches in between all along bed, leave needles in working position and K 2 r = 14 r.
COR, increase 1 stitch on both beds on opposite side of carriage 5 times = 10 r.
Tension 3½/3½
Bring pushers up on front bed 3 up x 1 down all along bed (or 2 & 1 or 1 & 1)
*N/AX – K 2 rows
N/AX – left arrow in, K 2 rows*
Repeat from * to * for 28 rows .
Tension 3/3
N/N K 3 rows.
COL, place stitches from front bed onto back bed.  Bring all needles back into working position on front bed, handle down.
K 1 row .
Knit 4 rows waste, drop stitches off needles on front bed, black strippers knit few rows waste, take off machine and then latch tool last bootee row.

Ties – t4, 3 sts, 180 rows, same yarn as bootees (I knit this on the Brother)

OK folks! At first I am just going to paste the pattern instructions straight in here, for those of you who know what a Knitting Machine is all about, go for it!

For beginners wanting to learn how to machine knit a Baby Set, I will slowly add the full instructions with photos and movies as I get the time.

After completing the Baby Beanie, please continue to the Baby Jacket or the Baby Booties.

Fae Mason’s Passap Baby Set – Beanie

One end Cashmillon & one end silky (low bulk)

52/51 (if you feel it is too small try 56/55)
Tension 3/3
Pink Strippers.
**Zig zag row from right to left.  Cast on comb in. Small weight outside each end of knitting.
Pushers on back bed 1 up 1 down
AX/N  – no arrows K 5 rows (no strippers in for 3 rows)
AX/N  – left arrow in K 2 rows.**   This = 8 r.
Tension 2½/2½
N/N K 20 r.
Tension 3½/3½
Pushers on front bed 3 up & 1 down (or 2 & 1 or 1 & 1)
*N/AX – K 2 rows
N/AX – left arrow in, K 2 rows*
Repeat from * to * for 52 rows (or 56 or 60 rows)
Tension 2½/2½
N/N K 10 r
Tension 2¼/2¼
Handle up Rib 1 x 1 for 10 r. Latch tool off or thread yarn through each stitch and pull up.

OK folks! At first I am just going to paste the pattern instructions straight in here, for those of you who know what a Knitting Machine is all about, go for it!

For beginners wanting to learn how to machine knit a Baby Set, I will slowly add the full instructions with photos and movies as I get the time.

After completing the Baby Jacket, please continue to the Baby Beanie or the Baby Booties.

Fae Mason’s Passap Baby Set – Jacket

One end Cashmillon & one end silky (low bulk)

Back  -  56/55 sts                     Fronts  -  28/27
Tension 3/3
Pink Strippers.
**Zig zag row from right to left.  Cast on comb in. Small weight outside each end of knitting.
Pushers on front bed 1 up 1 down
N/AX  – no arrows K 5 rows (no strippers in for 3 rows)
N/AX  – left arrow in K 2 rows.**   This = 8 r.
Tension 3½/3½
Pushers for Pattern 3 up & 1 down (or 2 & 1 or 1 & 1) on front bed
*N/AX – K 2 rows
N/AX – left arrow in, knit 2 rows*
Repeat from * to * for 112 rows
Tension 3/3
Transfer 2 sts from each end on front bed to back bed.
N/N knit 20 rows (all needle rib)
Tension 2½/2½
N/N, handle up, 1 x 1 rib. Starting from the left transfer first st from front bed to 3rd st on back bed and push the now empty needle out of work, then the 4th on the back to the new 1st on the front bed. Repeat every alternate st to end. When you reach the end (right) you need to transfer the 2nd last stitch on the back bed to the 3rd last position, then the last st to the 2nd last st.
Needles should look like this (“.” Represent “out of work” needles)
111.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.111 Back Bed 30 stitches.
1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1.1      Front Bed
Knit 20 rows.
N/N transfer front bed stitches to needles on back bed with stitch on them,
(black strippers).
Tension 3, knit 1 row right to left.
Few rows waste yarn, cast off last row of garment with size 14 needles.
25-26 cm finished neck.  Crochet 3 treble, 2 chain, 3 treble around neck/part fronts

Sleeves  -  28/27
Tension 3/3
Pink Strippers.
**Zig zag row from right to left.  Cast on comb in. Small weight outside each end of knitting.
Pushers on front bed 1 up 1 down
N/AX  – no arrows K 5 rows (no strippers in for 3 rows)
N/AX  – left arrow in K 2 rows.**   This = 8 r.
Tension 5½/5½
CX/CX, K 12 r.

Tension 3½/3½

Pushers for Pattern 3 up & 1 down (or 2 & 1 or 1 & 1) on front bed

* N/AX – K 2 rows
N/AX – left arrow in, K 2 rows *
Repeat from * to * for 72 r.
Tension 3/3
N/N K 20 rows (all needle rib)
Tension 2½/2½
N/N, handle up, 1 x 1 rib K 20 rows
N/N transfer front bed stitches to needles on back bed with stitch on them,
(black strippers), 111.1.1.1.1.1.1.1.1.1.1.1.1.1.1.111-16 sts for sleeves & fronts.
Tension 3, K 1 row right to left.
Few rows waste yarn, cast off last row of garment with size 14 needles.

fin.

Those familiar with machine knitting, knitting machine patterns and the terms they use, follow the Pattern lines. Otherwise, the Beginner sections are best Towards the end, Pattern and Beginner begin to merge, mainly because there is no short way to explain what the steps are and hopefully the leaners are becoming more familliar with the machine knitting process by the end.

The short version as a PDF can be downloaded by right clicking and “Save Target/Link As..” here Machine Knitting a Sock Pattern , other patterns can be found on the Machine Knitting Patterns, Free! page

Yarn: 4 ply (Sock yarn, wool containing some synthetic for better wear)

Tensions (shortened to T for the remainder):

For the 1 x 1 Rib Band ’0′ (for cast on & circular row)
’3′ for main rib
’6′ stocking stitch (st = stitch)
NOTE: Set the tensions on both main carriage and ribber to be the same.

Pattern: With main yarn, T ‘0′ cast on 75 stitches in 1 x 1 rib (zig zag row right to left).

Beginner: Prepare to cast on by moving every second needle to the B position, working from the middle for 75 needles width (do to the 37 mark on the left, and 38 on the right, both beds, the bottom bed will be offset slightly to the left) . Moving the carriage side to side once will line them up nicely, finish with the carriage on your right, reset your row counter to zero.

Now thread the yarn through the carriage, and between the 2 beds, and hold it firmly under the knitting machine beds.

Set the tension to ’0′ and slide the carriage and ribber left over the needles, this will knit the yarn creating a zig zag row.

NOTE: Put your ribber cast on comb on. Simply remove the fine wire and feed the comb up from under the beds so that the ‘teeth’ seperate each zig zag, then feed the wire back through the weight comb and let it hang. Add 2 weights evenly near the sock.

Pattern: Knit ’1′ circular row.
Beginner: With the carriage still on the left, set the carriage to do a circular row. Press in right hand Part button on main carriage, this means it will only knit from right to left on the main bed. On the ribber, push up the left Part button to P-R, this will only knit from left to right on the ribber bed. Now slide the carriages right, then back to the left. Set counter to zero.

Pattern: Remove circular setting, T ’3′, knit 33 rows in rib.
Beginner: Remove circular settings on the carriage and ribber by setting it back to normal, change the tension setting on the carriage to ’3′ and knit to 33 rows.

Pattern: Transfer all stitches to main bed, decrease 7 stitches evenly along bed.
Beginner: Using the double eyed tool, move the stitches from the bottom bed to the main bed, thus creating a whole row. Drop the ribber bed down one notch. Then decrease 7 stitches evenly along bed. See the video below for a demo.

NOTE: This produces a rib at the top of the sock that is better shaped to the body of the sock than if you don’t do this decrease.

You should end up with something like this.

Pattern: Close gaps keeping centered.
Beginner: Using a transfer tool, move all stitches from each end, towards the middle to close gaps, this is time consuming and fiddly. See below.

Pattern: T ’6′, knit 1 row in stocking st.
Beginner: Change the tension setting on the carriage to ’6′ and knit 1 row (right to left) stocking (normal/plain) stitch using the main carriage only.

Pattern: Take work off with a few rows of contrasting waste yarn.
Beginner: Break or cut the yarn and replace with waste yarn, using a contrasting colour is highly recommended. Knit a few rows with the waste yarn, 6 to 10 rows will be ample. Break waste yarn and knit until the sock falls off. Remove cast on comb and weights. Leave the carriage on your right.

Pattern: H pitch on ribber, 34 needles on each bed to working position.
Beginner: To the left of the knitting machine bottom bed / ribber, you should see a slider shaped like a smile that has P – H, slide it right to H, this is so that the needles don’t touch each other when protruding. Now bring 34 needles on each bed to working position B.
NOTE: The main bed right most needle must be outside (to the right) of the ribber bed right most needle.

Pattern and Beginner: With the wrong side of the last knitted row facing you, start on the right centre needle and place the left most loop of the sock onto that needle (NOT the waste, fold it under, away from you). Now roll the rib into a circle and place what was the right most loop onto left centre needle and 1 loop onto all remaining needles along the main bed. This should put the center seam of the rib at the back of the sock and on the main bed.

Pattern and Beginner: Now work your way along the bottom bed, 1 loop from the sock (NOT the waste) onto each needle.

For those only just learning Machine Knitting, maybe this will help.

Pattern: T ’6′ knit 40 circular rows (80 on row counter) keep downward pressure.
Beginner: Set your tensions to ’6′, set your row counter to zero. Set your carriages to do a circular row again, if you have forgotten, see just under the casting on instructions, it involves the Part buttons. Thread your main yarn back on, knit 40 circular rows (80 on row counter) keep downward pressure. This will be the length up your leg of the sock.

Machine knitting the sock heel

Pattern and Beginner: Drop the ribber bed half way only, change to main bed only (presser). T ’5′ on main carriage. Set “holding cam lever” (N-H-I) to (H). Remove the circular knitting setting on the main carriage.

On the top bed, assuming your carriage is on the right, bring the furthest needle from the carriage to holding position (left most needle, all the way out), knit 1 row (from right to left), place yarn under the protruding needle (now closest to carriage), bring furthest needle from carriage (right most) to holding position, knit 1 row, place yarn under right most needle, protrude 2nd left needle, knit 1 row, now place the yarn under the 2nd left needle but over the 1st…
Repeat until there are 8 needles in holding position on each side of the sock. Main bed only!

NOTE: Keep downward pressure on the sock underneath the main bed throughout the knitting of the sock heel as the sock will grow longer under the main bed as the heel takes shape, ribber bed side will not.

Pattern and Beginner: You should have 8 needles out on each side with the carriage on your right, and the yarn under the 8th innermost right needle but over the first 7 needles on the right…
Push the innermost (8th) left needle back to knitting position D. Knit 1 row, place the yarn under the new innermost (7th) left needle but over the remaining 6 left needles. Push the innermost right needle to knitting position D. Knit 1 row.
Place the yarn under the new innermost (7th) right needle but over the remaining 6 right needles. Push the innermost (7th) left needle back to knitting position D. Knit 1 row. Repeat until all needles are in except the rightmost needle the carriage should end up on the left with rightmost needle only remaining out.
Remove presser, replacing with ribber, raise ribber bed to knitting position and set main carriage back to circular knitting.

NOTE: Next row has to be worked on the ribber only, which it should because in circular knitting settings from the above step, moving from left to right only knits on the ribber bed. Make sure the remaining needle in the holding position on the main bed is on the outside of the needles on the ribber bed.

Pattern and Beginner: T ’6′, knit 1 row (left to right). Place yarn under remaining needle. Set “holding cam lever” (N-H-I) to N and set knitting machine for circular knitting again. Reset counter.

Knit 60 circular rows (120 on row counter). This will be the foot.

Machine knitting the sock toe

Pattern and Beginner: Using a double pointed transfer tool, decrease 1 stitch each end on both beds (pick up 2 stitches, but only move 1 needle space inward, meaning the 2nd last needle has the last stitch on it but the 3rd last has 2 stitches). Knit 2 circular rows (twice back and forth with the carriage, ends on same side). Do this 5 times.

Pattern and Beginner: Using a double pointed transfer tool, decrease 1 stitch each end on both beds again. Knit 1 circular rows (twice back and forth with the carriage, ends on same side). Do this 6 times. Hopefully you have 12 stitches remaining!

Break yarn leaving about 30cm and replace with more waste yarn, knit a few circular rows and break waste, knit until sock falls off!

Grafting the sock toe by hand

Pattern and Beginner: The video explains it best, its hard to put into words! This grafting method leaves no seam, the most comfortable sock you will ever knit! Grab a needle and thread the 30cm of yarn you had left onto a needle. Poke it through from the outside into the space beside the last knitted stitch, so that it comes out on the inside.
Fold the waste yarn out over the toe to expose the single row of main colour, stitching from inside to outside of the sock (out of stitch), starting with the stitch nearest you and closest to the end you came through on. Another out of stitch through the opposing side of the toe.
In to stitch (from outside to inside) you came out of first (closest to you), then out of stitch in the next one along (2nd closest to you). In to stitch first stitch on opposite side, then out of stitch in the next one along (2nd one opposing side). Repeat this until toe hole is closed! Poke the needle through to the inside of the sock at the end of the last graft.

Remove the waste yarn from the sock toe. Remove waste yarn from rib.
Sew up the rib and end all threads!

Hooray!

One Sock! Repeat for a 2nd one, or put eyes on the toe for a sock puppet

You could also try using “Variegated sock yarn” for some fancy coloured socks! Christmas happens every year!

The whole “machine knitting a sock for beginners” process, with me asking questions, taking photos and video, redoing parts that I didn’t understand, and the final hand stitching parts, took a little over an hour. Without me “helping”, I’m sure a pair of machine knitted socks could be produced in this time. The time it took to get all this onto a website, a football team could be wearing new socks…

The knitting machine being used for the guide is the Brother KH-940 without the ribber attached, and acrylic 4 ply yarn. If you are using acrylic, and the single bed, like this example, the finished product will have rolled edges, pressing will fix that. We will assume you have some documentation regarding how to thread your particular knitting machine and have threaded it. For casting on, the “simple cast on” will work on Brother knitting machines and the “e” wrap method should work on the majority of Japanese machines eg. Brother, Singer, Toyota and Empersal. Passap knitting machines use a different method which will be covered in the Passap pages.

I find using photos and videos as a learning tool easier than a whole lot of writing, so I have included them also.

Learn how to cast on

Simple Machine Knitting Cast On

Move your K-Carriage to the right of the needle bed (knitting carriage, the bit you grab onto and move side to side to knit). Locate all the needles to the A position (positions are marked on each side of the needle bed). Click your weaving brush levers into the up position.

Working from the center (so the counter works reliably) push every needle for your required width (the width of the finished product will be smaller that the width the needles represent) to the B position. Now push alternate needles to position E (all the way out). Pull your pre threaded yarn from under the K-Carriage, across the E needles, resting it in front of the bed but behind the hooks of the needles. Angle the end of the yarn you are holding down and away from the K-Carriage.

Be sure to hang onto the end, not pull tight, just don’t let it go. Slide the carriage from right to left, it might feel like things aren’t right, but it should go fairly easily, slide it until you have cleared the pushed out needles.

The carriage will move the needles automatically so don’t panic that they aren’t in the same position as where you left them. Keep holding the end of the yarn and move the carriage back to the right, once again moving all the way past the moved needles.

Guess what? You have cast on! Keep a grip on the end of the yarn for another couple of rows. Return the weaving brush levers to the down position, now is also a good time to add some weights to the emerging knitted product to keep an even tension on it. Try using a cast on comb if you have one. Uneven tension makes the finished product knit unevenly with some holes larger than others. If you don’t have any weights, pull lightly downward on the knitted article as you knit so it doesn’t drop stitches due to the lack of downward pressure keeping the yarn on the needles.

This simple cast on is great for making quick swatches of machine knitted fabric to assess the tension and also the number of stitches and rows required to create a finished article from a particular yarn, the results do vary from yarn to yarn.

Learn how to “e” Wrap Cast On

Named from the shape the yarn makes on the needles, it gives a nicer finish, but is a bit more fiddly. Putting this process into words may come later, but I find it easier to see whats going on rather than read it. Simply click the play button below to see e wrap casting on being performed.

Learn how to cast off

Simple Machine Knitting Cast Off

Once again, a text translation may come after, but for now, the video below will give a visual guide to a simple machine knitting cast off.

Looser Machine Knitting Cast Off around gate pegs

This method of casting off produces a nicer finish more reliably keeps a uniform tension. It achieves this by keeping the but the stitches you are casting off on the knitted article on or near its needles on the gate pegs that protrude from the front of the bed. The result is the article cannot bunch up or fall down, pulling the yarn unevenly.